![]() ![]() They’re very wide-angled and very bright, so you need to check that you’re happy with that before you commit. However, you might choose one for an office space, your garage (mainly if you spend your evenings and weekends working on your car), or even for an open plan room in your home. They might be used as a security light for your garden or to illuminate a warehouse. Many LED floodlights use the same E26 base as a regular A19 light bulb.įloodlights tend to be used for larger spaces, both indoor and outdoor. If the base type matches the fitting, and it has enough space in a fixture then the bulb will work. You can install an LED floodlight bulb in any socket and fixture in which it fits. Can You Put An LED Floodlight Bulb In A Regular Socket? That’s unlike many other LED lights, which have a driver lowering the voltage to 12V, since that’s often enough to power an LED.Ĭertain bulbs share this trait with floodlights – GU5.3 spotlights are another type of spotlight, but they’re too small to have a driver, and so run on mains voltage instead. LED flood bulbs tend to run on the regular circuit voltage of your home – 120V in the US. A19 bulbs are more ambient – doing a similar job to a floodlight but for a smaller space, and with a gentler light. Spotlight bulbs are directional, and tend to be used as task lighting – illuminating the important space directly below. Their purpose is to produce a high amount of light across a wide beam angle to illuminate a large space. LED floodlights are designed to be used outdoors or in indoor settings where a lot of light is needed – often in commercial settings. Regular lighting is lower – expect around 300 lumens for a spotlight (since you tend to use multiple spotlights for a room) while an average for an A19 bulb is closer to 600 lumens, though you can get A19 bulbs with a higher wattage that are a much more powerful light. Typical LED flood lamps will average around 1500 lumens. The brightness of a light depends on the wattage, but floodlights are typically brighter than other bulbs, because their maximum wattage averages higher. A19 bulbs will range from 4 watts to 13 watts normally. GU10 spotlights use as little as 1.8 watts but can range up to 11 watts – though they are typically 5 watts. That does average out as more than a typical smaller indoor bulb, but not by much – certainly nowhere near the wattage drawn by older incandescent light bulbs. The average wattage of an LED floodlight is between 12 and 18 watts. Typical Wattage Of Floodlights And Regular Lights And while an A19 bulb will have wide beam angles too, they aren’t as powerful a light and so they produce light in a more gentle, even spread, compared to the intense wide brightness of a floodlight. Smaller PAR bulbs are what you’d use for most indoor spotlights, with a more narrow beam. ![]() BR lights tend to have a wider beam, while PAR bulbs are a little more directional, as they only have a slight raise to the bulb head. Most floodlight bulbs are BR lights, though you can also get PAR lights – standing for Parabolic Aluminized Reflector. That means a BR40 is more than double the size of typical spotlight bulb (GU10s measure around 2″ wide) and around twice the size of a common A19 light bulb (which are 2.4″ wide). They’re typically BR30 or BR40 lights, which mean they have a width of 3.74″ and 4.72″ respectively across the bulb head. While floodlight bulbs will typically have the same E26 base as a regular light bulb, the actual size of the bulb head is much larger. Here’s a summary table of how a BR40 LED bulb compares to GU10 spotlights and A19 bulbs normally used indoors: Difference Voltage – floodlights tend to use mains voltage, while many LEDs (but not all) are low voltage.Purpose – floodlights are normally used in a commercial or outdoor setting, though not always.Luminosity – floodlights generate much more light.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |